Note |
---|
ATTENTION |
Note |
---|
IMPORTANT PlugIn version <2.5.0:
PlugIn Version = 2.5.0
|
The comfort remote control of your Dimplex heat pump
With the Dimplex SmartRoomHeating App your Dimplex heat pump is now online. With the SmartRoomHeatingApp have you from anywhere (Note system requirements) Access to your Dimplex heat pump directly via the iPhone®, iPad® and iPod® touch.
In combination with the Smart RTC room temperature controller, the room temperature can now be set differently for up to 20 rooms via the app. The standard integrated heat pump manager intelligently and automatically ensures maximum efficient operation.
The most important functions at a glance:
Fast and convenient monitoring of the heat pump status
Change of mode and setpoint temperatures
Increase and decrease times of heating curves
Access to home ventilation units of the ZL ... V / ZL ... H / ZL ... H-C series
SRH App | |
editor | Glen Dimplex Germany GmbH |
Operating system IOS | from IOS 8.0 |
Version 2.6.6 | 23.10.2019 |
Android operating system | Not planned! |
languages | German |
Table of Contents |
---|
System requirement
The minimum system requirement for using the SmartRoomHeating App is an internet access¹, a Dimplex heat pump with heat pump manager WPM 2006, WPM 2007, WPM EconPlus or newer, as well as one NWPM extension for integration into the network, with at least Firmware A1.5.0. The SRH app requires iOS 8.0 or higher. The smartphone must have active internet access¹ to be able to access the heat pump.
¹When accessing the Internet, additional costs may arise depending on the DSL and mobile phone contract.
Info |
---|
NOTE |
installation
The installation of the SRH App takes place via the AppStore with your smartphone or iTunes.
to register
Before you can start, the SRH App and the heat pump with the server. Registration is necessary so that both sides can speak to each other.
The following figure shows a schematic of the communication after the registration has been completed.
Installation and registration video
An installation and registration video of the SRH App made available: https://youtu.be/JzFDgzrCGRs
Registration of the SRH app
To register the SRH App will
a user name of your choice
a freely selectable password
the serial number of the heat pump
needed. The serial number (serial number) can be read off the type plate of the heat pump.
Info |
---|
NOTE Example:
|
When registering the SRH App the fields serial number, password and user name must be filled out and the registration confirmed. The serial number is then checked. If the registration was successfully completed, the system ID and the system key are reported back. The system identifier and the system key are then required to register the heat pump. The comparison of the SRH App with the heat pump.
Info |
---|
NOTE If you reinstall the SRH APP the server address is already preset. |
Registration of the heat pump
A NWPM extension with the Firmware A1.5.0 or newer and one Plug-in needed. If a plug-in is already installed, the status message "Ready" is output. If the status message "Ready" is not displayed, the plug-in has not yet been installed.
The heat pump is registered via the menu «settings»-«Remote control" carried out
Note the server address monitoring.gdts.one!
"System ID" and "System key" access data from the registration of the SRH App in the interface and set the online access to "Yes" and save
A short time later, the successful login is displayed in the status
link
If the above steps have been carried out successfully, the SRH App started and carried out the login using the specified access data. After a successful connection, the start screen of the SRH App displayed.
Info |
---|
*NOTE |
Error messages
Since not all software versions of the heat pumps have yet been released, a check is carried out first. If the test is successful, the SRH app starts in the home screen. If the test is unsuccessful, a message will be displayed.
Versions
version | date | description |
---|---|---|
2.6.6 | October 2019 |
|
2.6.5 | 03/08/2018 |
|
2.6.4 | 01/22/2018 |
|
2.6.2 | 11/29/2017 |
|
2.2.1 | 05/30/2016 |
|
2.1.4 | 03/10/2016 |
|
Contact
For further questions, information and suggestions, please send an email to:
ferndiagnose@gdts.one
with the additional information of:
Device designation
Software version